Cisco 642-813 Test Prep, Recenty Updated Cisco 642-813 Study Guide Is What You Need To Take
New VCE and PDF– You can prepare Cisco 642-813 exam in an easy way with Flydumps Cisco 642-813 questions and answers.By training our vce dumps with all Cisco 642-813 the latest questions,you can pass the exam in the first attempt.
QUESTION 1
Observe the topology in the exhibit. HSRP is configured between RTB and RTC with RTC as the active router. SW2 is configured as the root bridge for the Spanning Tree Protocol. What will happen if the serial connection of RTC is down?
A. STP will not need to be recalculated because RTB will take over as active router
B. RTB and RTC will flap between active and standby because the timers for the STP are greater that the timers for HSRP
C. All traffic will automatically forward to RTB
D. SW3 will take over as the new root bridge
Correct Answer: B QUESTION 2
Refer to the exhibit. What statement is true based upon the configuration of router R1 and router R2?
A. Router R1 will become the active virtual gateway
B. Router R2 will become the active virtual gateway
C. The hello and hold timers are incompatible with multi-homed BGP
D. The hello and hold timers are incompatible with OSPF type 5 LSAs
E. Router R1 will become the master for Virtual Rouer 1, and router R2 will become the backup for Virtual Router 2
F. Router R2 will become the master for Virtual Rouer 1, and router R1 will become the backup for Virtual Router 2
Correct Answer: A
QUESTION 3
Which First Hop Redundancy protocol cannot be configured for interface tracking?
A. HSRP
B. GLBP
C. VRRP D. SLB
E. RPR
F. RPR+
Correct Answer: C
QUESTION 4
Refer to the exhibit and the partial configuration on router R1 and R2. Hot Standby Routing Protocol (HSRP) is configured on the network to provide network redundancy for the IP traffic. The network administrator noticed that R2 does not became active when the R1 serial0 interface goes down. What should be changed in the configuration to fix the problem?
A. R2 should be configured with a HSRP virtual address
B. R2 should be configured with a standby priority of 100
C. The Serial0 interface on router R1 should be configured with a decrement value of 20
D. The Serial1 interface on router R2 should be configured with a decrement value of 20
Correct Answer: C QUESTION 5
Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4. When Link A fails, router R2 (Link B) becomes the active router. Which router will assume the active role when Link A becomes operational again?
A. The primary router R1 will reassume the active role when it comes back online
B. The standby router R2 will remain active and will forward the active role to router R1 only in the event of its own failure
C. The standby router R2 will remain active and will forward the active role to router R1 only in the event of Link B failure
D. The third member of the HSRP group, router R3, will take over the active role only in event of router R2 failure
Correct Answer: A QUESTION 6
Given the configurations on SwitchA and SwitchB, which two statements are true? (Choose two)
A. The trunk is currently using the ISL trunking protocol
B. The trunk is currently using the 802.1q trunking protocol
C. By default, the trunk can only support one VLAN, and only that single VLAN is transmitted across the trunk
D. By default all VLANs will be transmitted across this trunk
E. By default, SwitchA and SwitchBs FastEthernet 0/1 port will not generate DTP messages
Correct Answer: BD
QUESTION 7
Which three items are types of PVLAN ports? (Choose three)
A. Community
B. Dedicated
C. Desirable
D. Isolated
E. Native
F. Promiscuous
Correct Answer: ADF
Our material on our site Cisco 642-813 is exam-oriented,keeping in view the candidates requirements and level of understanding. Cisco 642-813 materials are in the most popular and easy-to-use PDF version. You can use it on any devices with you anywhere.
